亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Ghana

Release time:2023-11-07 17:47:38 Hits:147 Current position: Home > News

This article mainly introduces:

Ghana hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Ghana trunnion cylinder

(Ghana trunnion cylinder,produced by Hengyu Hydraulic Co., Ltd)

trunnion cylinder are widely used in Ghana,because of no need for deceleration device,long service life,smooth movement.So our company has designed trunnion cylinder for customers from Ghana.

Introduction to trunnion cylinder:

The "O" ring can be used as an auxiliary seal inside the trunnion cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the trunnion cylinder, and can be completely sealed.

At the rated pressure, the thrust of the trunnion cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the trunnion cylinder is related to the diameter of the trunnion cylinder, but not to the stroke of the trunnion cylinder. Moreover, the larger the trunnion cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the trunnion cylinder.

The repair method of trunnion cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When the control pressure of the hydraulic system is too low, the trunnion cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about trunnion cylinder:

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩成人影片久久| 久久少妇的诱惑视频| 永久黄片免费在线观看| 亚洲欧美日日| 五月亭影院网在线观看| 久久草精品国产| 丝袜不卡一区| 熟女在线三区| 伊人超碰在线不卡| 精品午夜理论电影| 久久影视无码偷偷| 人妻丝袜一区二区| 日韩有码在线免费观看| 亚洲一区二区中文字幕| 人人色午夜| 日韩蜜臀爱爱| 久久久久精网站| 亚洲欧洲淫荡视频| 免费一级特黄网站| 2015国产精品视频| 日韩欧美国产日本| 女教师亚洲一区| 久久久国产精品盗摄| 外国熟女偷拍| 91av在线激情| 久久黄争片| 爆操人妻| 精品免费大国偷自产| caoporn个人免费| 亚洲少妇二区| 日本电影经典久久久久| 国内精品久久人妻| 好紧好湿好爽好紧视频在线观看免费| 亚洲 日韩 中文字幕 丝袜诱惑| 大香蕉婷婷逼干| 黄色电影亚洲一区二区三区| 美女AV网站免费| 日本久久无| 波多野 久久| 精品国产久久久久久| 最新国产精品一区二区三区久久综合|