亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

baling press cylinder Sold to Angola

Release time:2023-11-07 17:48:00 Hits: Current position: Home > News

This article mainly introduces:

Angola hydraulic cylinder,baling press cylinder manufacturer,baling press cylinder

Angola baling press cylinder

(Angola baling press cylinder,produced by Hengyu Hydraulic Co., Ltd)

baling press cylinder are widely used in Angola,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed baling press cylinder for customers from Angola.

Introduction to baling press cylinder:

The wear of the hard chromium plating layer of the baling press cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

The quality of the baling press cylinder can not be ignored in the purchase of the baling press cylinder. The baling press cylinder is the main component of the baling press cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. baling press cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of baling press cylinder is deep hole processing, which has always troubled the processing personnel.

When producing oil baling press cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

baling press cylinder use should try to avoid sealing belt into the baling press cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the baling press cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the baling press cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

Answers to some questions about baling press cylinder:

When the cylinder is tested, why can't the pressure be maintained with the balance valve?
Because the oil into the oil chamber through the hydraulic lock on the control oil circuit through the other side of the spool, the original valve is designed in this way. It locks the circuit after the oil supply circuit loses pressure, on the contrary, if you keep supplying pressure, it is always in the state of opening the other side of the one-way spool. So this valve can't be used in the test.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕系列一区二区| 美女午夜福利网| 国产99成人精品视频免费福利| 亚洲欧美日韩国产精品一区二区| 国产精品老色鬼视频| 一二区成人电影院| 欧美一本| 国产理论亚洲天堂av| 欧美 中文 日韩 另类| 美女男人亚洲亚洲| 日韩无卡无码视频| 国产成人综合网| 99大片| 欧美视频play| 九九九九成人精品免费| 亚洲欧美日本不卡青椒| 日韩无码视频网站| 国产一区欧美大香蕉| 国产成人黄色W.91| 金粉艹B在线观看| 欧美亚洲 成人小说| 欧美老熟熟女一区二区三区| 三级后入| 亚洲成人色拍| 天天日天天干天天澡| 丝袜人妻在线| 97国产精品人妻无码网站| 99精品中文字幕在线不卡| 麻豆美女在线精品全裸| 少妻少妇精品一区二区| 2020性无码| 啪视频在线播放观看| 日本黄色片一级中文字幕| 精品美女91下载| 亚洲三级香蕉AV| 大鸡巴用力抽插逼逼嗯啊视频| 卖B视频免费| 亚洲丰满女同hd| 中文字幕人妻被公喝醉在线| 五月婷婷第一页| 久久久精品十八禁|