亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Korea

Release time:2023-11-15 10:41:47 Hits:119 Current position: Home > News

This article mainly introduces:

Korea hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Korea trunnion cylinder

(Korea trunnion cylinder,produced by Hengyu Hydraulic Co., Ltd)

trunnion cylinder are widely used in Korea,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed trunnion cylinder for customers from Korea.

Introduction to trunnion cylinder:

When the trunnion cylinder is customized, if there are high requirements for the quality of the trunnion cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the trunnion cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the trunnion cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When the trunnion cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the trunnion cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

When producing oil trunnion cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

What kind of process is used in the trunnion cylinder to make high-quality trunnion cylinder products: the body is the main component of the trunnion cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The trunnion cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the trunnion cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the trunnion cylinder increases by 25%. If the service life of the trunnion cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. trunnion cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the trunnion cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and trunnion cylinder are stuck or the trunnion cylinder is blocked. At this time, no matter how to manipulate, the trunnion cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the trunnion cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about trunnion cylinder:

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

How to use a solenoid valve to control the expansion of a cylinder? Doesn't the solenoid valve only control on/off?
Use the solenoid valve P into A-B (generally equipped with oil circuit board) to connect the oil inlet interface at both ends of the cylinder, and the solenoid valve can be realized by power off (refer to the solenoid valve 2B2L, different solenoid valve actions are different).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩,欧美,国产一区三区| 日韩草久久久天码影院| 日韩免费中文不卡| 午夜日日日日| 少妇野外真实激情视频| 日本伦理一二三区| 偷拍一区吧| 国产五月天精品99| 久久黄色电影一级片| 曰韩久久久成人电影| 国产AV小说一区二区三区| 国产 欧美 另类 制服 变态| 欧洲国际三级片一区二区| 欧美的一区| 东京热中文字幕日韩| 国产区精品熟女| 美女动态高潮黄色网站| 在线观看免费国产| 国产 精品在线不卡| 在线观看亚洲国产性| 91久久久久久久久久电影| 在线一区二区三区四区www| 丝袜美女三级| 亚洲噜一噜| 日韩男女做爱高清| 国产91丝袜诱惑| 嫩模筱慧三点全开福利视频| 五月丁香一级A片视频| 午夜伦理视频在线观看| 国精一级A片网站| 99久久精品国产高一区一区三区 | 无码中字东京热| A屁视频一区二区三区四区| 国产美女无遮挡全部免费视频网站| 毛片中心8久久久久久久久久久久久| 日本99久久久国| 亚洲无AV一区二区三区久久| 91日韩专区在线观看| 麻豆偷窥裸体美女在线观看 | 人多欧美啪啪啪操大鸡巴| 嗯嗯啊不行视频|