亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

synchronous hydraulic cylinder Sold to Uzbekistan

Release time:2023-11-16 08:45:04 Hits:122 Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Uzbekistan synchronous hydraulic cylinder

(Uzbekistan synchronous hydraulic cylinder,produced by Hengyu Group)

synchronous hydraulic cylinder are widely used in Uzbekistan,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed synchronous hydraulic cylinder for customers from Uzbekistan.

Introduction to synchronous hydraulic cylinder:

synchronous hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the synchronous hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

synchronous hydraulic cylinder piston rod material introduction: In general, we use 45 steel to produce synchronous hydraulic cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

Improve the service life of the synchronous hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the synchronous hydraulic cylinder (such as the synchronous hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the synchronous hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the synchronous hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single synchronous hydraulic cylinder exhaust.

synchronous hydraulic cylinder installation precautions: Before installing the synchronous hydraulic cylinder into the system, the parameters on the synchronous hydraulic cylinder label should be compared with the parameters when ordering. The base of the synchronous hydraulic cylinder must have sufficient stiffness, otherwise the synchronous hydraulic cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

Answers to some questions about synchronous hydraulic cylinder:

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
99riav视频一区二区| 男女性生活级毛片| 日韩精品www欧美| 少妇射进去精品久久| 欧美亚洲91久久麻豆露脸| 中日韩欧美乱码三区无码| 国产产欧美国产在线观看| 国产精品一麻豆视频播| 日韩一区二区三区情人| 久久精品国产亚洲AV天美电话| 国产xxnx麻豆| 99精品白浆在线| 日韩国产精品中文| 久搡在线观看| 国内黄色精品| 精品久久久久久亚洲综合网站| 销魂美女免费网站视频一区| 日韩欧美成人影院| 欧美日韩性色生活| 欧美日本视频一区二区三区| 午夜激情免费国产| 在线观看艹逼视频| 日韩一二级在线观看| 日韩成人性交网站在线| 国 产 欧 美一 区 二区| 色诱综合天天| 大香尹三级片| 欧美狠狠舔一区二区爽啊| 亚洲综合专区在线| 婷婷综合在线基地| 欧美美女操逼视频操逼视频| 操B爽大全| 久久99在线视频88| 丝袜美女国产在线| 国产一级久久| 成人一级亚洲欧美香蕉| 日韩欧美一区二区三中文字幕| 日本久久久精品无码| 日本精品人妻色免费 - 百度| 第一页 中文字幕 18| 亚洲日韩三级久久|