亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Germany

Release time:2023-11-21 09:56:28 Hits: Current position: Home > News

This article mainly introduces:

Germany hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Germany stacker cylinder

(Germany stacker cylinder,produced by Hebei Hengyu company)

stacker cylinder are widely used in Germany,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed stacker cylinder for customers from Germany.

Introduction to stacker cylinder:

The definition of the minimum stable speed refers to the minimum movement speed of the stacker cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the stacker cylinder that undertakes different work has different requirements for the minimum stable speed.

When the stacker cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the stacker cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

When the stacker cylinder needs to be stored for a period of time, please follow the recommended methods: The stacker cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the stacker cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil stacker cylinder should not be in direct contact with water vapor for a long time. The stacker cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the stacker cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the stacker cylinder Before working, the stacker cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the stacker cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The difference between the plunger stacker cylinder and the piston stacker cylinder is that the piston in the stacker cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type stacker cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Answers to some questions about stacker cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美三级又粗又硬| 久久和久久网站| 欧美日韩国产一区二区久久内射| 欧美三级片久久地址| 国产夫妻视频一区二区三区| 五夜激情天天爱夜夜操| 你懂的91视频国产| 成人五月天婷婷天| yiquerqu av| AV国产不卡在线播放| 久久不卡日韩不卡| 赵碰成人网| 欧美日韩视屏| 午夜激情小福利| 日韩少妇高潮久久久| 四虎www色色| 精产国品一区二区你懂的| 成人精品久久婷婷一区二区 | 亚洲色一区二区Av| 伊人色婷婷欧美色图在线观看免费| 日韩精品网站尤物| 国产色婷婷八区| 精品国产天线2024| 一本道视频一区二区| 大香蕉手机在线视频98| 国产精品久久久久久Av免| 在线免费呦呦V| 精品成人福利网| 欧美丝袜在线一区| 日韩少妇后入后入| 国产特级片三区四区| 产成人精品曰本亚洲79_久久久| 91人人蜜桃| 日本无码口爆吞精一区| 欧美日韩欧美综合| 被操爽视频| 久久99精品中文| AI换脸亚洲精品在线| 国产WWW一区二区| 女性各种b免费视频| 在线不卡免费高清Av三区|