亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

unidirectional cylinder Sold to Congo

Release time:2023-11-08 10:36:25 Hits: Current position: Home > News

This article mainly introduces:

Congo hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

Congo unidirectional cylinder

(Congo unidirectional cylinder,produced by Hebei Hengyu company)

unidirectional cylinder are widely used in Congo,because of simple structure and reliable operation,no transmission clearance,high work efficiency.So our company has designed unidirectional cylinder for customers from Congo.

Introduction to unidirectional cylinder:

In the case of serious wear on the inner surface of the unidirectional cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the unidirectional cylinder manufacturing process for replacement. The unidirectional cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

unidirectional cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the unidirectional cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the unidirectional cylinder. c. The unidirectional cylinder seal is extruded, if the O-ring is obviously extruded at the unidirectional cylinder seal, replace the unidirectional cylinder seal.

The repair method of unidirectional cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the unidirectional cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Answers to some questions about unidirectional cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
农村熟女激情| 欧美暗黑丰乳肥臀二区| 99国产日韩电影| 在线电影无码av| 自拍偷拍综合欧美| 天天操天天干91AV| 1024欧美一区二区日| 成人区精品一二三四五六七八九区| 人妻熟女-第六页-| 欧美色色色区| 五月激情丁香网| 久久国产在线一区二区| 欧美深夜福利一区二区三区| 橙色一区二区三区在线观看| 大鸡插小穴在线观看| 久操这里只有精品1| 大香蕉官网在线视频| 日韩美女风骚美女操逼视频| 日韩 欧美 一起| 色花堂日逼AV| 欧美特黄一级大色片| 日屄视频网站免费观看| 免费看草 视频| 亚洲性色论坛| 九一午夜精品| 国产av性爱| 黄色免费试看| 超碰国产剧情演绎欧美精品| 韩日清纯欧美射精| 精品人夷妻高清| www操逼视頻| 男子调教美女内射视频在线观看视频| 亚洲欧美成人无码在线| 日韩伦理一二三区| caoporn首页| 夫妻性生活视频网站| 天堂噜噜噜| 北条麻妃av作品高清在线| 日韩综合在线第一页一页| 熟女,乱轮,丝袜,欧美| 新超碰av|