亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

spring return cylinder Sold to Guatemala

Release time:2023-11-28 10:55:23 Hits: Current position: Home > News

This article mainly introduces:

Guatemala hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

Guatemala spring return cylinder

(Guatemala spring return cylinder,produced by Hebei Hengyu company)

spring return cylinder are widely used in Guatemala,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed spring return cylinder for customers from Guatemala.

Introduction to spring return cylinder:

The piston seal of the spring return cylinder is the main element to prevent leakage in the spring return cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

The coordination of the sliding parts of the spring return cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

Before the spring return cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

The repair method of spring return cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about spring return cylinder:

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

How to judge the failure of forklift hydraulic cylinder?
The common faults of the hydraulic cylinder of forklift truck are mainly crawling, insufficient thrust, working speed decline or even stop. Generally, crawling occurs at low speed. The main reason is that the air stored in the cylinder is not cleared. In addition, excessive or uneven mechanical friction can also cause crawling. Such as the piston and the piston rod different heart, the piston rod full length or local bending, the cylinder hole straightness is poor, the cylinder is drum shaped or has a large taper, the cylinder thin finish decline or produce hair, the cylinder installation accuracy is out of whack, the piston rod nuts at both ends of the screw too tight to make its concentricity is poor, the oil seal screw too tight friction is too large, will cause crawling.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
一区二区三区四区五区久久| 中文字四季AV| 三级毛视频| 久久狠周| 中文无码日本欧美| 91国产日韩| 操逼视频中国啊嗯嗯| 怪物av网站| 欧美 国产 经典 日韩 一区| 国产区欧美区二区一区| 艹逼视屏在线观看| 人妻高跟一区二区| 大香蕉国产AV女优| 日本久久久久久久极品黄色| 日日夜夜精品一区二区亚洲| 日韩欧美一级一级一级不卡| www.日韩欧美日韩欧美日韩日韩 | 日韩久久双| 日本在线不卡二v| 天天幼插幼av| 校园黄色影院| 好屌妞,这里有精品| 情激综合网| 欧美蜜臀一区二区在线播放| 天天日天天要天天搞| 人人爽人人三级片| 爆操欧美3D国产| 大香蕉一区二区av| 日韩狠狠干网站| 亚洲AV综合区一区二| 麻豆免费1区| 亚洲女人张开腿让男人捅| 中文久久毛片| 日韩亚洲国产不卡| 三级视频在线观看视频了| 擦老熟女一区二区三区| 日韩三级AV一区| 色呦呦直通| 内射亚洲少妇逼逼| 美女被操b软件| 亚洲久久大几八成人在线|