亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

single rack cylinder Sold to Turkmenistan

Release time:2023-12-05 14:27:16 Hits:129 Current position: Home > News

This article mainly introduces:

Turkmenistan hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Turkmenistan single rack cylinder

(Turkmenistan single rack cylinder,produced by Hengyu Hydraulic Cylinder Factory)

single rack cylinder are widely used in Turkmenistan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed single rack cylinder for customers from Turkmenistan.

Introduction to single rack cylinder:

The single rack cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the single rack cylinder should pay attention to: the operation should be as far away from the single rack cylinder as possible, to avoid falling objects, knocking, rubbing the single rack cylinder coating. When cleaning the single rack cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the single rack cylinder when the oil temperature exceeds 70 ° C.

When the single rack cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

If the seal of the single rack cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and single rack cylinder, and the phenomenon of "pulling the single rack cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The wear of the hard chromium plating layer of the single rack cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about single rack cylinder:

How to achieve hydraulic cylinder self-locking?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil self-locking is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.

How to repair the bent oil cylinder correctly?
If the bending oil cylinder leaks, the most direct way is to replace the seal ring. Most of the sealing rings used by domestic bending machines are made in Taiwan and Japan, so the service life of the sealing ring is still relatively long. If the bending oil cylinder used by the customer leaks oil, then when replacing the seal ring, be sure to choose a high-quality and durable seal ring. In this way, the replaced cylinder will not leak oil for a long time.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
av福利频道| 天天干天天射天天爽天天日| 天天天天色| 日韩欧美成人高清在线视频| 欧美特黄一级片特黄一级片| 久久精品中文在线| 日韩三级视频电影| 我要看操逼试频| 无码二区久久| 午夜性17| 欧美夫妻生活黄色录像XX| 男女激情啪啪啪国产区| 日本一二三区在线观看视频| 精品分享日韩有码| 啊啊啊啊啊啊好大在线免费| 久久人妻砰砰砰| av日在线一区| 久久精品296| 日本午夜少妇内射| 日韩人妻在线播放观看| 国产精品日韩精品 欧美精品| 亚洲诱综合| 久久久爽久| 国产中文二区中文字幕 | 黄片117| 国产精品流白浆免费软件| 国产麻豆1区2区3区精品| 激情五月天综合网| 亚洲www成人网站在线观看| 久久久久久久国产精品无套区99| 超碰caoporn国产精品在线| 色诱惑视频免费| 亚洲一区二区三区成人电影| 超级碰碰碰碰碰碰碰碰碰碰碰| 国产一区二区福利网站| 精品人妻少妇中文嫩草av无码| 日本一区二区机械| 天天躁,狠狠躁,夜夜踩| 亚洲黄色av色色av| 香蕉乱码| 五十六十路熟女视|