亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering cylinder Sold to Chile

Release time:2023-12-11 09:05:25 Hits:140 Current position: Home > News

This article mainly introduces:

Chile hydraulic cylinder,steering cylinder manufacturer,steering cylinder

Chile steering cylinder

(Chile steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

steering cylinder are widely used in Chile,because of no need for deceleration device,long service life,smooth movement.So our company has designed steering cylinder for customers from Chile.

Introduction to steering cylinder:

If the steering cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the steering cylinder. The internal parts of the steering cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the steering cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steering cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the steering cylinder bore processing is out of whack. Because the piston and steering cylinder, guide rail and piston rod are relative If the steering cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling steering cylinder weight composition and calculation. The weight of the steering cylinder is composed of the steering cylinder diameter, the outer diameter and weight of the steering cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

When the steering cylinder is customized, if there are high requirements for the quality of the steering cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the steering cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the steering cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

If the steering cylinder slips or crawls, please check whether there is astringency inside the steering cylinder, because the internal parts of the steering cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the steering cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steering cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Most of the failure of the steering cylinder is because there is a foreign body in the steering cylinder into the failure of the steering cylinder, the most problematic is that it is difficult to determine when the foreign body is into the steering cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about steering cylinder:

Is there a national standard for the testing of hydraulic cylinders?
Generally speaking, the cylinder test is carried out according to JB/JQ20302 Allowable leakage of cylinder in pre-factory leakage test. GB2879 hydraulic cylinder piston and piston rod dynamic seal groove type, size and tolerance. GB6578 hydraulic cylinder piston rod dust ring groove type, size and tolerance. GB7938 hydraulic cylinder and cylinder nominal pressure series, etc.

How to control the speed of the hydraulic cylinder?
The speed of the hydraulic cylinder is only related to the flow, so the control speed is to control the flow of the hydraulic oil, which is generally adjusted by the throttle valve in the system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久久久综合一区二区| 麻豆视频二区视频| 妹子每日高清亚洲| 亚洲经典1区2区3区| 男人天堂色播| 一区二区剧情| 狠狠色综合网久久久久久| 久久综合不卡| 麻豆传媒精品视频在线| 日本1区2区三级电影| 久久好吊妞精品视频| 欧美亚洲日韩二| 欧美综合激情一区| av在线看片福利| 午夜韩日欧美| 国产 视频 无码 一区二区| 亚洲一区二三区免费在线观看| 成人a∨男人的天堂| 国产精品香蕉亚洲中文版| 日B日夜免费视频| 国产欧美在线播放免费观看| 久久妻91| 国产无码电影网战| 黄色午夜黄色午夜片| 成人人成日韩欧美| 精品91白丝| 夫妻一级视频| 91,欧美,日韩| 久福利| 色中文第二区| 天堂AVc0m| 综合图片区一区| 国产99日本在线高清| 亚洲一级黄片大全| 日本熟妇乱淫免费播放| 久久视频夜夜干| 亚洲性交网站在线播放| 亚洲熟女天天干| 大鸡巴爆操在线观看| 日本高清www色午夜| 国产高清大片一线二线三线 |