亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Algeria

Release time:2023-11-08 15:23:47 Hits: Current position: Home > News

This article mainly introduces:

Algeria hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Algeria stacker cylinder

(Algeria stacker cylinder,produced by Hengyu Group)

stacker cylinder are widely used in Algeria,because of powerful torque,clever hydraulic energy conversion,high work efficiency.So our company has designed stacker cylinder for customers from Algeria.

Introduction to stacker cylinder:

The quality of the stacker cylinder can not be ignored in the purchase of the stacker cylinder. The stacker cylinder is the main component of the stacker cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. stacker cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of stacker cylinder is deep hole processing, which has always troubled the processing personnel.

Protection of the stacker cylinder surface: During the dismantling process, safety protection should be carried out on the stacker cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the stacker cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the stacker cylinder should be cleaned up in time.

Piston stacker cylinder is widely used in hydraulic transmission. When the stacker cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the stacker cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the stacker cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

stacker cylinder is the most important part of construction machinery, the traditional processing method is: broaching stacker cylinder block - fine boring stacker cylinder block - grinding stacker cylinder block. The rolling method is: broaching stacker cylinder block - fine boring stacker cylinder block - rolling stacker cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the stacker cylinder block is about 1-2 days, rolling 1 meter of the stacker cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the stacker cylinder increases by 25%. If the stacker cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality stacker cylinders, you must take the rolling production process. After the stacker cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about stacker cylinder:

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女尤物一区二区三| 色国产综合视频| 超碰免费 中文字幕日本| 色女日B免费视频| 爱久久午夜影院一区| www.国产吊| 少妇久久综合网| HEYZO少婦AV無碼精品| 极品美女的逼| 又黄又粗又猛的视频| 成人网站精品成人欧美| 后入在线极品| 日韩欧美在线视频播放| 久久国产精品美女| 国产精品成人久久| 又大又长又粗中文视频| 国产欧美在线观看一12| 夜夜夜爽,夜夜夜要| 性感少妇内射后入| 99无码区富婆| 久久亚洲私人国产精品99| 擦骚逼吸奶子啊啊啊嗯视频| 2020久久天天躁狠狠夜夜| 不卡wwwxxxx中国日本不卡视| 性色生活片在线观看无码一区小说| 最新福利地址| 亚洲天堂a^| LSJ在线观看老司机| 哎呀国产的大鸡巴片子| 中文字幕AV二区三页| 国产婷婷五月天缴情| 又大又粗又猛又黄的视频| 九九九九黄色电影| 骚鸡巴艹骚逼洞视频| 国产在线观看剧情一区二区| 欧美美女内射视频三区| 欧美日韩制服人妻| 日韩久久伦理| 情欲视频在线播放| 天天AV不卡网| 日少妇综合|