亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Ireland

Release time:2023-11-10 08:35:18 Hits: Current position: Home > News

This article mainly introduces:

Ireland hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Ireland track steering cylinder

(Ireland track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

track steering cylinder are widely used in Ireland,because of long service life,smooth movement,no need for deceleration device.So our company has designed track steering cylinder for customers from Ireland.

Introduction to track steering cylinder:

If the track steering cylinder slips or crawls, please check whether there is astringency inside the track steering cylinder, because the internal parts of the track steering cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the track steering cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the track steering cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the track steering cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Before the track steering cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

track steering cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the track steering cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about track steering cylinder:

What is the bearing capacity of the HOB cylinder?
The normal specification of HOB is 140 kg pressure, which is more commonly used in the market, and there are clear marks on the cylinder, 210 kg is a strengthened version of HOB, generally customized cylinders are also clearly marked on the above, when the specific use of the cylinder, the maximum use pressure is marked on the cylinder.

Is there a way to make the cylinder stop pushing when it hits something hard during the process of pushing?
The simplest solution is to press the stop switch, this switch has a mechanical type, touch the object on the action or send a stop signal, through the operation of the motor control cylinder; There is also an induction switch, that is, when the hydraulic cylinder expands to the range of the induction switch can sense the signal, it sends a signal to let the motor act, resulting in the corresponding action of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
香蕉一级黄色片视频| 人妻无码中文视频| 欧美aaa级性爱网| 精品xxxxxx一区| 成年黄色亚洲| 国产激情熟女| 午夜福利一二三区免费精品久久久亚 | 青青草综合在线观看| 日本一区二区在线2| 国产成人视频91推荐| 日韩av伦理在线| 家熟女导航| 欧美黄片视频免费在线观看| 亚洲 欧美 日韩 综| 激情福利精品| 美女福利短片在线免费观看| 国产理论孕妇在线| 撸撸色图二区| 热久视频在线视频观看| 日韩欧美少妇| 亚洲精品在线观看视频你懂得| 韩日小电影无码一区二区| 色AV高清无码| 国产午夜dy8888一区二区三区| 怡红院怡红院分站| 亚洲天堂一区区区| www.久久久亚洲天堂| 伊人影院婷婷综合在线| 伊人激情福利| 婷婷丁香五月一区二区三区| 日韩在线图片一区| 一区二区三区国产图片| 91人品一区二区三区| 亚洲精品久久片久久久久| 日韩免费黄色小电影| 大香蕉大香蕉国产| 日韩午夜色图片一区二区三区| 天天日天开爽| 无码一区二区三区四区不卡精品| 99热在线国产欧美| 中国字幕人妻在线|