亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Colombia

Release time:2023-11-12 11:05:58 Hits:124 Current position: Home > News

This article mainly introduces:

Colombia hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Colombia track steering cylinder

(Colombia track steering cylinder,produced by Hebei Hengyu company)

track steering cylinder are widely used in Colombia,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed track steering cylinder for customers from Colombia.

Introduction to track steering cylinder:

In the case of serious wear on the inner surface of the track steering cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the track steering cylinder manufacturing process for replacement. The track steering cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

The difference between the plunger track steering cylinder and the piston track steering cylinder is that the piston in the track steering cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type track steering cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Most of the failure of the track steering cylinder is because there is a foreign body in the track steering cylinder into the failure of the track steering cylinder, the most problematic is that it is difficult to determine when the foreign body is into the track steering cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

When installing the track steering cylinder pipe, the pipe should be cleaned after installation, and should not pass through the track steering cylinder block, and the by-pass pipe must be installed in front of the oil port of the track steering cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the track steering cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the track steering cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about track steering cylinder:

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
自拍偷拍区 国模| 17草网站在线观看| 91麻豆精品在线观看| 91久久婷婷国产麻豆精| 艹熟女的视频| 久久图片小说一区| 午夜99久久成人黄| 精品丝袜脚久久久久久久不不| 加勒比视频成人| 亚洲色图人妻视频| 亚洲成人有码成无码综合网| 亚洲av无码成人专区片在线观看| 美女一片日黄女| 囯产美女扒B毛视频| 国产精品都市伦理| 一本a久久a综合| 国产网站色欲| 97国产一区二区三区在线视频| 亚州丰满很很操| 久色在线视频| gogo亚洲高清大胆美女人体| 在线日韩伦理在线| 操到高潮国产精品| 日本一区二区黄色网| 麻豆传媒AV,一区二区三区| 艹逼免费网站视频| 欧美大鸡巴双插一区二区| 骚逼被操了网站| 在线又粗又打。| 高清不卡 一区二区 有剧情| 欧美电影h在线在线看免费版| 丁香五月加勒比| 99伊人大香蕉在线播放| 青青草香蕉91视频| 91骚妇操在线| 快射视频一区二区| 欧美四区在线| 伊人色色伊人| 国产精品av中文字幕,| 狠狠狠欧美一区二区欧美| 亚洲三级1234|