亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push and pull the cylinder Sold to Tanzania

Release time:2023-11-12 15:33:16 Hits: Current position: Home > News

This article mainly introduces:

Tanzania hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

Tanzania push and pull the cylinder

(Tanzania push and pull the cylinder,produced by Hengyu Group)

push and pull the cylinder are widely used in Tanzania,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed push and pull the cylinder for customers from Tanzania.

Introduction to push and pull the cylinder:

When the long-stroke push and pull the cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in push and pull the cylinder head seal damage, oil leakage, and piston sleep in the push and pull the cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the push and pull the cylinder; The piston and the piston rod are connected with a spherical joint.

When installing the push and pull the cylinder, the axial ends of the push and pull the cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the push and pull the cylinder, there is axial expansion. If the two ends of the push and pull the cylinder are fixed, all parts of the push and pull the cylinder will be deformed. When disassembling the push and pull the cylinder, it is strictly forbidden to hammer the push and pull the cylinder and the piston surface, such as the push and pull the cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

push and pull the cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

When the oil pressure of the push and pull the cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about push and pull the cylinder:

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

What is a two-way hydraulic cylinder?
Bidirectional hydraulic cylinder definition: The bidirectional hydraulic cylinder uses the oil as the working medium, transmits the movement through the change of the sealing volume, and transmits the power through the pressure inside the oil. The two-way cylinder has at least two oil ports, which are used to connect the hydraulic tubing, and control the extension and retraction of the cylinder by pressing.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
成人超碰在家线| 大鸡吧亚洲无码在线| caoporn超频国产| 成人九九精品| 欧美成人XXXXX| 日本免费视频一区二区三区| 精品 漫画 区 一二| 国产欧美日韩下一页在线| 午夜福利乱码中文字幕| 欧美精品人妻一区二区三区大一片| 欧美日韩亚洲综合视频| 天天日天天射天天插天天爽| 夜夜躁首页| 国产精品亚洲色欲| 黄片区域在线观看| 国产免费av综合片在线观看| 久久国产精品密臀| seyouyou在线视频| 久久国产午夜AV| 久久AV影院在线| 精品视频久久久久| 天天日天天插天天射天天爽| 在线观看艹b| 艹大骚笔视频| 中文字幕久久性爱| 国产美女菊花爆乳| 午夜a在线试看91| 日本美女三区四区| 麻豆二一区| 欧洲亚洲国产综合在线| 亚洲AV在线偷拍自拍| 日本五十路一区| 精品91色虎BB| 欧美一区在线一| 日韩激情中文字幕在线| 日韩欧美成人视频网站| 极品一区hd| 极品少妇视频一二区| 一色哥一区网站| 午夜福利视频看看| 中文字幕一区二区人妻秘书|