亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Slovenia

Release time:2023-11-12 15:33:17 Hits: Current position: Home > News

This article mainly introduces:

Slovenia hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Slovenia shearing machine cylinder

(Slovenia shearing machine cylinder,produced by Hengyu Group)

shearing machine cylinder are widely used in Slovenia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed shearing machine cylinder for customers from Slovenia.

Introduction to shearing machine cylinder:

The wear of the hard chromium plating layer of the shearing machine cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

In the process of using the shearing machine cylinder, sometimes such a problem will occur, the shearing machine cylinder can not act immediately after the instruction of the shearing machine cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil shearing machine cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

shearing machine cylinder installation precautions: Before installing the shearing machine cylinder into the system, the parameters on the shearing machine cylinder label should be compared with the parameters when ordering. The base of the shearing machine cylinder must have sufficient stiffness, otherwise the shearing machine cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

Do not regularly check the damage of the chrome layer of the shearing machine cylinder: completely extend the shearing machine cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the shearing machine cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the shearing machine cylinder seal. Welding slag is strictly prohibited on the surface of the shearing machine cylinder.

Answers to some questions about shearing machine cylinder:

Why does excavator cylinder oil leak?
Under normal circumstances, the leakage of hydraulic cylinders is divided into internal leakage and external leakage. The external leakage is generally due to damage to the oil seal at the extended end of the piston rod and needs to be replaced. Internal leakage is generally because the oil seal on the piston is damaged, you can try to replace the oil seal here, if the replacement will also leak, then check whether there is damage to the inner wall of the cylinder.

Is a hydraulic cylinder and a jack the same thing?
Strictly speaking, no. Although the hydraulic principle is used, and even some of the longer jacks are similar to the cylinder, the internal structure of the two is different. There is a check valve inside the jack. After the top lift, the check valve locks the hydraulic oil circuit, and the hydraulic oil only enters and does not exit after the check valve locks, and can be lowered to complete a reciprocating movement. The cylinder is usually connected to the distribution tube to control the movement, and works with a wide variety of distribution valves and distribution systems according to different needs. The jack only needs a simple check valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产短丝袜在线视频| 天天干天天艹天天日天天日| 天天玩天天干天天爽天天上| 精品99一区二区| 久操这里只有精品6| 精品不卡内射中出亚洲| 啪啪啪啪啪一区二区三区| 二区一区无码在线| 人妻少妇精品视频二区三区98| 操骚逼大鸡巴| 亚洲免费人体视屏| 97精品久久天干天天天按摩| 三级片韩国久久久久久久久久| 舔阴帝视频无码| 人妻激情在线视频| 色情婷视频在线视频| 强奸久久久久| 久久国产乱理在线观看| 过程AV一区二区| 无码熟妇人妻AV在线电影| 欧美大鸡巴操骚逼的大全的录像| 中文字幕 - 有料视频| 无码aⅴ免费一区二区三区| 日逼黄色绿像| 日韩欧美一区二区综合免费| 国欧美 一区二区三区| 欧美特一区黄片| 国产黄色片久久久久| 欧美性xxxxx极品少妇| 亚洲国产天堂婷婷综合在线播放| 高潮免费视频久久| 国产我91在线| 人妻有码av中文字幕久久午夜| 亚洲综合三级在线观看| 九九中文免费视频| 婷婷五月天亚洲无码| 天堂 电影| 久热在线8| _欧美成人精品第一区二区三区| 欧美拍拍一级黄片| 女人考男人黄片免费看|